Bullet Sensors & Transducers e-Digest, Vol. 82, Issue 8, August 2007: Product News

    (ISSN 1726- 5479)


Editorial Calendar 2007

Editorial Board

Submit an Article or Press Release

10 Top Sensors Products of 2006

Sensors & Transducers Journal 2006

Microbridge logo

Top 25 Downloaded Article

2000-2002 S&T e-Digest Contents

2003 S&T e-Digest Contents

2004 S&T e-Digest Contents

2005 S&T e-Digest Contents



Microbridge Dramatically Increases Accuracy of Temperature Compensation by More Than 10X with Flexible Rejustors



Montreal, Canada – August 13, 2007 Microbridge Technologies, Inc. introduced the MBT-303-A rejustor (re-adjustable resistor), the world’s first passive electronic Temperature Compensation (eTC) divider, ideal for managing temperature in precise analog circuits, optical systems, sensors, and power supply compensation and calibration across a wide range of military, aerospace, automotive, industrial, medical, and consumer applications.


The first in a family of resistor dividers and networks employing eTC technology, the MBT-303-A is a high accuracy dual 30K ohm divider (two resistors in series) where each resistor can be set to any value between 21K and 30K ohms with an accuracy of 0.01%.  Having two rejustor elements in the same package makes it easier to implement divider networks where resistors must be equally matched.


The MBT-303-A rejustor enables automated, independent adjustment of both resistance and the Temperature Coefficient of Resistance (TCR), which determines how resistance changes as the temperature changes.  Control of TCR that is independent of ohmic value enables the MBT-303-A to not only provide one to two orders of magnitude performance improvement for analog designs but also maintain consistency of resistance over an extended temperature range for circuits that require set-on-test calibration and compensation.


Until now it has not been possible to automate the adjustment process to compensate for temperature-induced drift using only analog components.  The eTC-based MBT-303-A, configured using Microbridge’s Rejust-it software, is the first passive device to solve analog problems in the analog domain using devices that are suitable for small volume niche markets to mass produced commercial products.


“This is perhaps the most important improvement to the resistor in more than a century,” said Bob Frostholm, vice president, Marketing and Strategic Alliances at Microbridge. “Automated calibration and temperature compensation in the analog domain has not been possible until now.  Analog engineers have been forced to use inadequate solutions in the past because this technology wasn’t available.  Rejustors based on eTC technology provide better response to the analog environment, yielding more accurate sensors, power-management devices, opto-electronics, and analog amplifiers.”


Variations in temperature can wreak havoc in even the most carefully designed analog systems since even small changes in temperature can alter performance and precision.  Additionally, manufacturing variances in circuits require that compensation be adjusted for each individual circuit.  Temperature compensation improves the precision of analog circuits in applications across the board, including increasing accuracy in catheters, tuning LCD panel displays, adjusting power supplies, calibrating sensors of all kinds, replacing digital potentiometers, and superseding less efficient compensation techniques such as fuses or laser trimming, to name a few.


Rejustors shift compensation in temperature-sensitive applications from an active process to a passive one.

Offset calibration vs. temperature compensation graph

Sensors Web Portal logo





Traditionally, engineers have had to compensate for changes in temperature using complex digital circuitry compromised of a microprocessor and D/A converters switching out fixed resistances. This approach is limited in accuracy (about .1% for a compensation circuit employing 10 switches) and consumes a notable amount of power. The additional circuitry involved also adds further uncertainties that reduce accuracy.


Rejustors eliminate many of the detrimental side-effects associated with digital compensation to achieve accurate and cost-effective temperature compensation.  In-circuit adjustability of both ohmic resistance and TCR, as well as support for positive and negative temperature coefficients, enables developers to apply compensation after devices such as sensors are fully manufactured and hermetically sealed.  Rejustors also eliminate the need for thin and thick film laser trimming currently used in IC manufacturing. The MBT-303-A requires no power source during operation, does not suffer from wiper resistance, and no external temperature sensor is required since the rejustor is its own temperature sensor as well as adjustment controller. Rejustors are capable of replacing complex digital potentiometers and can be used to raise the performance of lower cost analog circuits to the level of higher precision circuits.


“Rejustors are ideal for precision analog systems and will transform how the electronics industry compensates devices sensitive to temperature variations,” said  Richard Wawrzyniak, Sr. market analyst, ASIC & SoC. “Rejustors achieve true cost savings by reducing system complexity while increasing accuracy across the entire spectrum of electronic applications.”



Sacha Arts

Bella Vista Communications

Tel.: 408-356-3099

E-mail: s.arts@comcast.net



Back to S&T e-Digest page


1999 - 2013 Copyright ©, International Frequency Sensor Association (IFSA). All Rights Reserved.